Vertex Standard VX-2200 128 channel mobile 2-way radios are available in VHF and UHF bands. • Vertex Standard VPL-1 Programming Cable and CE82 Software. While we believe the information in this manual to be correct, Vertex Standard assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated. • 400 - 470 MHz (Type A) 450 - 512 MHz (VTX, Type D) 450 - 520 MHz (EXP, Type D) Number of Groups: 1 groups (VX-2100 Series) 8 groups (VX-2200 Series) Number of Channels: 8 channels (VX-2100 Series) 128 channels (VX-2200 Series) Power Supply Voltage: 13.6 V ±. • Specifications (EU Version) General Frequency Ranges: 400 - 470 MHz Number of Groups: 1 groups (VX-2100 Series) 8 groups (VX-2200 Series) Number of Channels: 8 channels (VX-2100 Series) 128 channels (VX-2200 Series) Power Supply Voltage: 10.8 - 15.6 V DC Channel Spacing: 12.5 / 20 / 25 kHz. • DSUB 15-pin Accessory Connector Pin 1: AF IN ( A Pin 6: EXT PTT NALOG NPUT External Microphone Input. They run the gamut: utilities, productivity tools, games, and everything else imaginable. Thousands of Mac developers offer apps from the Mac App Store, and they're yours for the taking. Mac app store download cache. Nominal input level is 6 Shorting this port to ground causes the transceiver to mV at 600-ohm. Be placed in the Transmit mode, while opening the When connect the External Microphone to this port, connection to this port returns the transceiver to the insert a 0.1 µF coupling capacitor between the micro. • FRONT-B-UNIT CONNECTOR RA0790900 REFLECTOR SHEET RA079000A (Lot. 1-8) RA079000B (Lot. 9-) CHASSIS RA078640A LIGHT GUIDE G6090173 VX-2200 FRONT PANEL Non-designated parts are available only as RA080360A RA0786300 part of a designated assembly. RUBBER PACKING LCD HOLDER RA0786900 T9318284 SUPPLIED ACCESSORIES. • Exploded View & Miscellaneous Parts Note. • Block Diagram. • Block Diagram Note. • Circuit Description 1. Circuit Configuration by Frequency 2-4. Audio amplifier Detected signal from Q1036 (NJM2591V) is inputted to The receiver is a double-conversion superheterodyne with Q1042 (NJM12902V) and is output through the band pass a first intermediate frequency (IF) of 67.65 MHz and a filter inside Q1042 (NJM12902V). • Circuit Description 3. Transmitter System 3-4-1. VCO While the radio is receiving, the RX oscillator Q1029 3-1. Mic Amplifier (2SK508) in the VCO generates a programmed frequency There are two micrphone inputs, J1004 (front) and J1006 (receive frequncy plus 67.65 MHz) as 1st local signal. • Beacuse of the BTL (Bridged TransLess) Amplifier circuit pair and alignment. Therefore, if a fault is suspected, con- used in the VX-2200/-2100, do not connect eather side of tact the dealer from whom the transceiver was purchased the speaker leads to chassis “ground.”. • The Alignment Tool Outline Installation the tool Install the CE82 (Clone Editor) to your PC. The re-alignment for VX-2200/-2100 series may use the “Alignment” menu of CE82. Action of the switches When the transceiver is in alignment mode, the action of PTT and KEY is ignored.
0 Comments
Leave a Reply. |